3B2/310 & TB+
rohan kelley
rk at bigbroth.UUCP
Wed Nov 23 08:48:41 AEST 1988
In article <557 at sactoh0.UUCP>, ejnihill at sactoh0.UUCP (Eric J. Nihill) writes:
> I am going to be installing a TB+ on a 3B2/310 and rather than
> re-invent the wheel, I would like to find out what S Register
> settings that others have used on 3B2/310 & 400's. Also, are
> there any tricks to setting up the Devices and Dialers files?
> I have the paper that TB sent, and it seems pretty straight
> forward.
> Thank-you;
> Eric
Eric - this is the memo I did when I installaed my telebit. It may help
you avoid some pitfalls.
MEMO
From: Rohan Kelley (novavax!bigbroth!rk)
Date: 4-14-88
Subject: TELEBIT MODEM SETUP
**** System paramaters and settings for modem. ****
The /etc/inittab line setup for 2400 baud (assuming use of tty33) should
be:
33:2:respawn:/usr/lib/uucp/uugetty -r -t 60 tty33 2400H # trailblazer modem
for 9600 baud, it would be:
33:2:respawn:/usr/lib/uucp/uugetty -r -t 60 tty33 9600H # trailblazer modem
for 19,200 baud it would be:
33:2:respawn:/usr/lib/uucp/uugetty -r -t 60 tty33 19200H # trailblazer modem
The ps -ft tty33 (at 2400 baud ) should look similar to:
root 16349 1 0 20:44:00 tty33 0:01 /usr/lib/uucp/uugetty -r -t 60 tty33 24
and at 19,200 baud ...
root 28981 1 0 11:13:03 tty33 0:01 /usr/lib/uucp/uugetty -r -t 60 tty33 19200H
The /etc/gettydefs line should be:
2400H# B2400 # B2400 SANE IXANY TAB3 HUPCL #login: #1200H
and
19200H# B19200 # B19200 SANE IXANY TAB3 HUPCL #login: #9600H
[You can confirm the /etc/inittab, ps -ft and /etc/gettydefs entries
with the commands:
grep 33: /etc/inittab
ps -ft 33
grep 2400H# /etc/gettydefs
The /usr/lib/uucp/Devices file must include these entries:
ACU tty33 - 19200 tbfast
ACU tty33 - 2400 tb2400
ACU tty33 - 1200 tb1200
ACU tty33 - 9600 tbfast
Direct tty33 - 19200 direct \D
The /usr/lib/uucp/Dialers file must include these entries:
tbfast =W-, "" A\pA\pA\pT OK \pATS51=254DT\p\D\r\c CONNECT\sFAST
tb2400 =W-, "" A\pA\pA\pT OK ATDT\D\r\c CONNECT\s2400
tb1200 =W-, "" A\pA\pA\pT OK \pATS50=2DT\p\D\r\c CONNECT\s1200
**** Settings for the modem itself ****
Reach the modem with the command: cu -l tty33 | tee (file_name)
Note, this will make a record of the standard out (screen) and in the
file named (file_name), which you can then print.
When you get the indication, CONNNECTED, give the command at [return]
until you receive the response, OK.
To set the modem to run at fast speed using the UUCP g protocol, the
command line when CONNECTED to the modem is:
at &f s51=254 s52=2 s54=3 s110=1 s111=30 s45=0 q6 &w [return]
Then type atn? [return]. The current modem settings will print in the
screen and also a copy is made in the file, file_name. The response
should look like:
at
OK
atn?
E1 F1 M1 Q6 P V1 X3 Version BA4.00
S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002 S07=040 S08=002 S09=006
S10=007 S11=070 S12=050
S45=000 S47=004 S48=000 S49=000
S50=000 S51=254 S52=002 S53=000 S54=003 S55=000 S56=017 S57=019 S58=003 S59=000
S60=000 S61=045 S62=003 S63=001 S64=000 S65=000 S66=000 S67=000 S68=255
S90=000 S91=000 S92=000 S95=000
S100=000 S101=000 S102=000 S104=000
S110=001 S111=030 S112=001
S121=000
N0:
N1:
N2:
N3:
N4:
N5:
N6:
N7:
N8:
N9:
OK
You can reset modem settings while CONNECTED to the modem with the command:
ats0=1. This command sets the contents of register 0 to 1. See page 3-8
of the manual.
=======================================================================
Rohan Kelley -- UNIleX Systems, Inc. (Systems and software for lawyers)
UUCP: ...{gatech!uflorida,ucf-cs}!novavax!bigbroth!rk
ATTmail: attmail!bigbroth!rk
3365 Galt Ocean Drive, Ft. Lauderdale, FL 33308 Phone: (305) 563-1504
"Go first class or your heirs will" -somebodyelse
=======================================================================
More information about the Comp.sys.att
mailing list